Matt circuit

 White-light LEDs are finding their way into many markets that incandescent bulbs once served. Flashlights are among the newer applications in which reliability, ruggedness, and ability to control the power draw of the LEDs make these devices attractive. With incandescent bulbs, the power management for the device is a simple on-off switch. However, the LEDs cannot operate directly from the two cells you typically find in most flashlights, because their required voltage is 2.8 to 4V, compared with a battery voltage of 1.8 to 3V. The power management has a further complication because the light output of the LED relates to current, and the LED's characteristics are extremely nonlinear with voltage. One approach to this problem is to boost the power supply with a current limit. A number of devices for LED applications are available; however, their current ratings are typically too low for the 1 to 5W that flashlight applications need. Buck IC Boosts Battery Voltage for White LED Circ...

The 555 circuit below is a flashing bicycle light powered with four C,D or AA cells (6 volts). Two sets of 20 LEDs will alternately flash at approximately 4.7 cycles per second using RC values shown (4.7K for R1, 150K for R2 and a 1uF capacitor). Time intervals for the two lamps are about 107 milliseconds (T1, upper LEDs) and 104 milliseconds (T2 lower LEDs). Two transistors are used to provide additional current beyond the 200 mA limit of the 555 timer. A single LED is placed in series with the base of the PNP transistor so that the lower 20 LEDs turn off when the 555 output goes high during the T1 time interval. The high output level of the 555 timer is 1.7 volts less than the supply voltage. 40 LED Bicycle Light Circuit Diagram   Adding the LED increases the forward voltage required for the PNP transistor to about 2.7 volts so that the 1.7 volt difference from supply to the output is insufficient to turn on the transistor. Each LED is supplied with about 20mA of current...

Low power amplifier with based on the IC (intregated circuit) TA7140 manufactered by TOSHIBA , its have original output power is 0,15 Watts, and the schematic diagram is monolithic power amplifier.Though the amplifier circuit has a low output , but the maximum voltage large enough to 30 volts. Part List : Resistor     = 100R Capacitors = 4u7F , 33uF , 100uF , 1000nF , 4700nF , 47uF IC              = TA7140P Technical information : Max. Voltage = 30 V Min. Voltage = 5 V Max. Output = 1 W RL                =  150 Ohm

Descriptipn: The following circuit shows about  741 IC For Simple Ham Radio Circuit Diagram.  Features: For filter out the interference signal. Component: Capacitor, IC, Inductor, Switch, Resistor, Battery.[electronics-project-design.co]

This is stereo audio amplifier with based on ICTDA2824S , Minimum voltage require 3 volts and maximum voltage 17 volts . Maximum output power 2 X 2 Watt , its low power amplifier. Output impedance  4 ohm. see schematic audio below :

Description Circuit showing a 9 volt power supply . Here we have used a bridge rectifier and 7809 ic for making this circuit.Where the ic regulate the output to 9 v,1 A .This voltage every time constant.Are you interested ? Circuit diagram with Parts list.    Notes.  If a current of 300 mA or above is required, fit a proper heat sink to the IC 7809 . If 1A bridge is not available, make one using four 1N 4007 diodes.

See this circuit below : Datasheet IC AN214 Vcc                = 6-18 V Pout               = 4,4W RL                  = 4 Ohm Ft                   = 50hz - 17Khz Icco                = 20 mA Package         = SIP2-9 Manufactered = MATSHUSHITA

This Schematic use IC AN374, this is mono amplifier and have output speaker 1 W with impedance 8 Ohm . Supply need 8Volt to 16 Volt , this Schematic you can use current Voltage 12 V. And better use the stabilizer with 7812 let the voltage stabil. The Effect will be on the sound so smooth. See this Schematic below  and see datasheet IC AN734 : Datasheet IC AN374 Vcc                = 8-16 V Pout               = 1 W RL                  = 8 Ohm Ft                   = 50hz - 17Khz Icco                = 12 mA Package         = SIP2-10 Manufactered = MATSUSHITA

This circuit equipped with 2 switches that are useful for loudness and filtering, on SW1 as the loudness , SW2 as a filter. It also equipped with direct  adjust of sound on Potentiometer 10k , but only useful as a master volume. Minimum Voltage  : 8 volts Maximum Voltage : 18 volts Maximum Power   : 2 X 13 Watt stereo Impedance Power  : 4 Ohms

Schematic Description : This Circuit Require voltage 12 -26 Volt. Good Voltage use is 16 Volt , Because its not too small and not too big Voltage. If use voltage that is to large it will quickly damage the IC. And if use voltage that is to small it will make less than maximum sound output. See this Circuit  and datsheet IC AN5265 Below : Click to Enlarge Datasheet IC  AN5265 Vcc                = 12-26 V Pout               = 2,3 W RL                  = 16 Ohm Ft                   = 40hz - 18Khz Icco                = 9,5mA Package         = SIP2-9 Manufactered =  MATSUSHITA

Varible Voltage regulator is a circuit that serves to supply a component or electronic equipment. It is similiar to the power supply, but on Variable Voltage regulator has an adjustable output. And adjusted by potentiometer not rotary switch. Voltage input about 1 Volt to 35 Volt Maximum. This is use 5A transformer but if you have a 3A transformer its can be use. Schematic below : To adjust the voltage use potentiometer on R2 . The variable voltage regulator lets you adjust the output voltage of  a fixed DC power supply between 1 Volt and 35 Volt DC. and will supply the output current in excess of 1.5 A. The circuit LM117K three-terminal adjustable output positive voltage regulator in a TO-3 can. *TIPS* If you use the 3A transformer its'nt to damaged the component, because of strong currents affect only the weak voltage. But that must be considered is the input voltage , use the desired equivalent in this setting. If the circuit requires 12 to 30 volt , 40 volt do not give the volt...

Schematic circuit power amplifier TDA1908 , or you can use IC TDA1908A . The circuit simple and easy to make the line PCB. See circuit and technical instruction below :  The circuit above can use to the 5.1 surround sound circuit , but you have made 6 circuit and to combine to 1 .  And suitable made to center speakers. Technical information : Minimum require voltage :  6 Volts Maximum require coltage :  30 Volts Maximum Power output   :  16 Watts Minimum Power output    :   4  Watts

Description for this Schematic : Power Supply need 16 to 34 Volt , this is very beautiful voltage because with voltage 16 -34 Volt will  be strong to make a loud sound. IC need AN272 ,this ic no similarities. You must use this IC. Ouput speaker Mono , with Power 5W and Impedance 8 Ohm. Click to Enlarge Datasheet IC AN272 Vcc                = 16-34 V Pout               =5 W RL                  = 8 Ohm Ft                   = 40hz - 18Khz Icco                = 20 mA Package         = SIP2-10 Manufactered = MATSUSHITA

Compressor Circuit with 570/571 Compandor IC circuit provide high gain for low amplitude input and provide low gain for high amplitude input. This action, in effect, produce a nearly constant amplitude even though the input has very high dynamic range (very high amplitude variation from time to time). The action of compression like this is needed in some situation, such as in maximizing modulation depth in broadcasting, or sustaining electric guitar signal which has very high variation between the plucking time and fading out.  The following circuit has complementary input/output characteristic and unity gain at 0.775 VRMS input. Voltage gain through compressor is square root of 0.7/Vin. Vin is average input voltage. This circuit  uses Signetics dual channel compandor IC.  570 has lower inherent distortion and higher supply voltage range (6-24 V) than 571 (6-18 V). Compressor Circuit with 570/571 

79xx is a widely known series of low-cost, fixed-negative-voltage regulators. These integrated circuits are available with output current of 100-150 mA (L series), 0.4-0.5A (M series), up to 1A (standard series), etc. They can be used in many applications other than regulators, audio power amplifier being one of them.  As shown in the circuit diagram, a simple stereo audio amplifier is built around two 7905 negative-voltage regulators (IC1 and IC2) and a few discrete components. The 7905 IC (a -5V regulator) used here is readily available. However, the circuit will also work with other 79XX regulators if appropriate power supply is used. Both channels shown in the diagram are identical. Hence the description below is only for the first channel. The quality of the output signal is within acceptable limits.  Circuit diagram : Stereo Power Amplifier Circuit Diagram   Regulator IC 7905 works as an amplifier for the voltages applied to common pin2 (Ground or GND). The minima...

Effect Echo is an electronic circuit that is used to delay sound or make an echo in an audio circuit . Using a circuit of echo is easy enough , we just set on the volume, and gain and trimpot near is rate of 20 K ohm to adjust how the desired echoes. This echo circuit using ic 4558D for additional amplifier and ic PT2399 as a major component that serves to echo , or repeat the sound output on the audio system. Click image to view larger  How to use it as follows : That is initially given the output of the mic input or other equipment. Then turn down the volume, and slowly raised, setting echo effect on the trimpot 20K. If not check back for the damaged to the circuit.

TDA 7012T FM Radio Receiver FM Radio Receiver IC TDA 7012T is very simple, but it has an FM radio receiver sensitivity and good selectivity. Single Chip FM Receifer cool name of IC TDA7012T 7012T TDA is to build an FM receiver requires a few additional components.  Feature contained in FM receiver IC TDA 7012T is quite tempting to an FM receiver. Among features an FM receiver TDA 7012T is a low-voltage applications micro affability arrangement (MTS), Frequency Loked Loop (FLL) to 76 KHz range and selectivity of FM receiver with RC Filter. In an article by FM Radio Receiver IC TDA 7012T can be seen in the FM receiver circuit which can be made​​. FM Radio Receiver with IC TDA 7012T From the picture above components to make the FM Radio Receiver IC TDA 7012T as follows: R1 = 8kΩ2 R2 = 10kΩ R3 = 390Ω C1, C3 = 10nF C2, C6, C9, C16 = 100nF C4 = 33pF C5 = 25pF trimmer C7, C10 = 1nF5 C8 = 820pF C11 = 1NF C12 = 68pF C13 = 220pF C14 = 47μF 10V C15 = 3nF3 L1 = 36nH L2 = 1μH, IC1 = TDA7021T Ho...

This schematic is great for those of you who frequent of use IC TDA2030 . In addition to the simple schematic  is also very clear , in modification accurate enough to make a sound that is more clear, soft , and loud. And if you interest to try this schematic. See this circuit , datsheet ic TDA2030 and TDA 2040 , and IC TDA2030 equation below : Datasheet IC TDA2030 Vcc                = 6-18 V Pout               = 14 W RL                  = 4 Ohm Ft                   = 20hz - 20Khz Icco                = 40 mA Package         = TO-220 Manufactered = TELEFUNKEN Datasheet IC TDA2040 Vcc                = 3-20 V Pout               = 20 W RL               ...

This circuit have applied to line detection of robot project, Good match between the transmitter and the detector is important for proper operation, especially if the hole is large. Robot with a simple object or obstacle detection. Infrared Transmitter detector pair sensors are relatively easy to implement, although involved some degree of testing and calibration in order to make correct. They can for the impediment, motion detection, transmitters, encoders are used, and the color detection. Infrared Emitter and Detector using IC 74LS14 Circuit Diagram: This can be done with a piece of rope stretched between and in accordance with LED and phototransistor. A length of stiff wire or plugs can be used to set the alignment. Another method that can be used for long distances is a laser pointer shone through a hole.